Velocity Scaling Calculator
Speed setpoint to measured speed: the feed constant of the axis from the gearbox and roller, or from two measured belt speeds.
Measured points
From the encoder
Measured points
From motor and roller
Measured points
From gearbox and roller
Measured points
From the signal range
—
—
—
—
Velocity scaling: setpoint to speed
Servo drives and closed-loop vector drives take a speed setpoint in rpm and hold
the motor there, so the only thing between the setpoint and the belt is the
mechanics: π × roller diameter ÷ gearbox ratio, the distance the belt
moves per motor revolution. That is the feed constant of the axis, the number a
drive or PLC axis configuration asks for to turn rpm into m/min, and the page
reports it next to the line.
Two measured speeds give the real feed constant. The factor between measured and theoretical is the correction to apply: 0.987 means the belt runs 1.3 % slower than the drawing says, usually belt creep on the drive roller or a roller whose effective diameter is not the nominal one. If the error is constant, correct the feed constant by that factor; if it changes with load, the belt is slipping and the scaling is not the problem.
A target speed in the check point returns the setpoint that reaches it, and the slider walks along the line to show the speed at any setpoint. For an open-loop drive that is set in hertz, use the frequency scaling instead: it includes the motor's slip. For rpm and a roller diameter alone, the surface speed calculator is the shorter route.
How it works
Every scaling here is one straight line: value = gain × raw + offset.
Two measured points fix it: gain = (value₂ − value₁) / (raw₂ − raw₁) and
offset = value₁ − gain × raw₁. The gain is the scaling factor a PLC or NC
axis asks for, and 1 / gain is the same thing the other way round: counts
per millimetre, hertz per metre a minute.
Measured more than twice? Add up to eight points and the line becomes the least-squares fit: the one with the smallest sum of squared distances to every point. Each point then shows its residual, how far it was measured off the line; one that stands out from the rest is usually a misread or a point taken while the axis was still moving.
Worked example. An encoder reads 0 at the home position and 100 000
counts 2500 mm further on. gain = 2500 / 100000 = 0.025 mm per count, 40
counts per millimetre, offset 0. The encoder itself says the same: 1000 pulses per turn,
read ×4, on a 100 mm feed, is 100 / 4000 = 0.025 mm.
Measured points define the line whenever they are filled in. The mechanics give the theoretical line: on its own it is the line, next to measured points it is the dashed comparison, and the measured one is divided by it. A factor of 0.97 means the belt runs 3 % slower than the motor and roller say it should. Each scaling has its own theory.
Encoder counts
feed ÷ (PPR × evaluation × ratio)
Position per count from the pulses per turn, the ×1/×2/×4 evaluation, the feed per turn and the gear ratio. Also the pulse rate at top speed, to check the input terminal.
Show this exampleDrive frequency
n ÷ f ÷ i × π × D
Speed per hertz from the motor's rated speed at its rated frequency, the gearbox ratio and the roller diameter. Measured below it: slip.
Show this exampleSpeed setpoint
π × D ÷ i
Speed per setpoint turn from the gearbox and the roller: the effective feed constant of the axis.
Show this exampleAnalog input
raw range → value range
A 4–20 mA or 0–10 V signal arrives as a raw integer, 0–27648 or 0–32767. Map its ends to the sensor's range and read any value in between.
Show this exampleCheck a point looks up any raw value on the line, or slides along it. Type what you measured there and the difference is shown, as a value and a percentage; if that point is the better one, make it point 1 or 2 and the line moves through it, or add it as a new point. A target value gives the raw value that reaches it: the frequency for a conveyor speed, the count for a position.
The offset is where the line crosses zero. For an encoder it is the reference position; for a drive it should be 0, and a line that does not pass through zero points to a minimum frequency, a dead band or a measuring error.
Questions
How do I calculate conveyor speed from motor rpm?
Belt speed = motor rpm / gearbox ratio × π × roller diameter. At 1000 rpm through a 10:1 gearbox on an 80 mm roller: 100 × π × 0.08 = 25.1 m/min, which is 25.1 mm of belt per motor revolution. That last number is the feed constant of the axis, and the page reports it next to the line.
What is a feed constant?
The distance the load moves per revolution of the motor: π × roller diameter / gear ratio for a belt or roller, the lead divided by the ratio for a screw. Drive and PLC axis configurations ask for it as feed constant, leadscrew pitch or distance per revolution to turn a setpoint in rpm into a speed in m/min, and a wrong one shows as a constant percentage error between setpoint and measured speed.
Why is the measured belt speed a few percent off the setpoint?
A servo or closed-loop vector drive holds the motor at the setpoint, so the difference is mechanical: the belt creeps on the drive roller under load, the roller's effective diameter is the drawing value plus part of the belt thickness or minus wear, or the gearbox ratio is not the one on the drawing. The page divides the measured scaling by the theoretical one; a factor of 0.987 is 1.3 % slow, and if the error is constant the feed constant can be corrected by it.
When do I use velocity scaling instead of frequency scaling?
When the setpoint is a speed in rpm, as a servo drive or a closed-loop vector drive takes it, so only the gearbox and roller sit between setpoint and belt. Frequency scaling starts from a VFD's output in Hz and includes the induction motor's slip. Set Hz on an open-loop drive: frequency. Set rpm: velocity.
Which setpoint do I need for a target speed?
Type the target speed in the check point and the page returns the setpoint that reaches it on the line: 30 m/min at 25.1 mm per revolution needs about 1194 rpm. The slider walks the check point along the line to read the speed at any setpoint.
Need saved scalings and PDF export?
View Plans